Bay Area Test Equipment Inc

Solar Chamber

Solar Chamber

Bay Area Test Equipment Inc is one of the leading solar chamber manufacturers and suppliers, welcome to buy and wholesale cheap and best solar test chambers from us. BTH Series Solar Test Chamber Solar test chamber reliability test of solar cells in the specification to be verified in wet,...

Product Details

Bay Area Test Equipment Inc is one of the leading solar chamber manufacturers and suppliers, welcome to buy and wholesale cheap and best solar test chambers from us.

BTH Series Solar Test Chamber  

Solar test chamber reliability test of solar cells in the specification to be verified in wet, frozen, temperature cycle, humidity test etc can be monitored during the experiment the continuity of the internal circuit of solar cells in order to determine whether the fault or failure, by the system solar battery failure can be determined.  

Test Model or test project

1). Damp Heat Test:

Test Condition:   95 ±2 ºC temperature range, and 95% ±5% R.H. humidity range 

Test Duration: last for 1000H, 

Test Purpose: To see the reliability of the module to withstand the effects of long-term penetration of heat and humidity. 

2). Humidity-freeze test  

Test Purpose: to see the ability of the module to withstand the effects of high temperature and humidity followed by sub-zero temperatures.

Test points and requirements:

-40ºC lowest temperature and 85ºC highest temperature 

Max temperature rising speed rate:200ºC/Hour=3.33/min

Max temperature falling speed rate:200ºC/Hour=3.33/min

24 hours per cycle, testing for 10 cycles, 240 hours (10 days)

3). Thermal cycle test;

Test requirements: -40ºC lowest temperature and 85ºC highest temperature

Temperature falling/rising speed rate:100ºC/Hour=1.67ºC/min,6 hours per cycle, 

Test Duration: 50~200 cycles

total testing time last 300 to 1200 hours (12.5 to 50 days) 

Applicable standards

IEC61646, IEC 61625, IEC 62108, IEC 61625,UL 1703,

Temp. Cycle 

Compare

High Temp. 

High Humidity

Low Temp

Temp. Change Rate

Cycle No.

IEC61215

85ºC/85±5%(20h)

-40ºC(0.5~4h)

High Temp. Rise& Fall(100ºC/h)
Low Temp. Rise& Fall(200ºC/h)

10

GB9535

85ºC/85±5%(20h)

-40ºC(0.5~4h)

High Temp. Rise& Fall(100ºC/h)
Low Temp. Rise& Fall(200ºC/h)

10

IEC61646

85ºC/85±5%(20h)

-40ºC(0.5~4h)

High Temp. Rise& Fall(100ºC/h)
Low Temp. Rise& Fall(200ºC/h)

10

GB18911

85ºC/85±5%(20h)

-40ºC(0.5~4h)

High Temp. Rise& Fall(100ºC/h)
Low Temp. Rise& Fall(200ºC/h)

10

UL1703

85ºC/85±2.5%(20h)

-40ºC(0.5~4h)

High Temp. Rise& Fall(100ºC/h)
Low Temp. Rise& Fall(200ºC/h)

10

IEC62108

85ºC/85±2.5%(20h)

-40ºC(0.5~4h)

High Temp. Rise& Fall(100ºC/h)
Low Temp. Rise& Fall(200ºC/h)

20
40


Temp. Cycle Compare

Low Temp

High Temp

Temp Change RateºC/h

Dwell Time

Cycle Number.

IEC61215

-40±2ºC

85±2ºC

Max. 100ºC/h

Min.10min

50, 200

GB9535

-40±2ºC

85±2ºC

Max.100ºC/h

Min.10min

50, 200

IEC61646

-40±2ºC

85±2ºC

Max.100ºC/h

Min.10min

50, 200

GB18911

-40±2ºC

85±2ºC

Max.100ºC/h

Min.10min

50, 200

UL1703

-40±2ºC

90±2ºC

Max.120ºC/h

30~105min

200

IEC62108

-40±2ºC

65ºC,85ºC,110ºC

10cycle/day

10min

500,1000,2000

IEC62108

-40ºC

65ºC,85ºC,110ºC

18cycle/day

10min

500,1000,2000

IEEE1513

-40ºC

90ºC,110ºC

0.9~7.5ºC/min

Min.10min

250,500

IEEE1513

-40ºC

90ºC,110ºC

Max.100ºC/h

Min.10min

100,200

IEEE1513

-40ºC

60ºC,90ºC

Max.100ºC/h

Min.10min

50,200

Standard Features:

* SUS304stainlesssteel+arcweldingseamlesswelding

* Fireproof PU+ glass fiber wool insulationmaterial
* Multi-layerglassobservationwindow+ Autoheating function
* Full-opening +double wing type door+ 10,000 times tested lock
* One Φ50mm portholescable port
* Coatedfinishing (colorsavailable)or SUS304
* Adjustable feet andheavy-duty castors

* High quality craftsmanship, modular design and construction

* Water and electricity separation system

* Fullsystemfunctionswitchesandindicatorlights
* Allwiringcolorcodedandlabeled
* Systemfaultstatusindicators
* Over-temperatureprotectionandalarmswitch
* Balancedloadon3phasepower
* Powerleakageprotection
* Overheatingprotection
* Overpressureprotection
* Overcurrentprotection

* CFC free refrigerant, in line with international standards

* Adopting international famous compressor ,parts and components

* No condensation and no frost design

* Coppertube/aluminumfincoolingcoilsavailable
* Air/Watercooledcondenser
* Highefficiencyplatetypeheatexchanger
* Dualhigh/lowrefrigerationpressurelimitswitches
* Overloadprotection for compressor


* Internal/External humidification

* Pt-100 sensor

* Fastresponsestainlesssteelarmoredhumidifier
* ReliableSSRnon-touchcontrolofhumidity
* Humidifierfaultprotection,overtemperatureprotection

* 7-inch color LCD touch screen
* Operation mode: programmable/ singe point setting
* Sensor:PT100 (electronic sensor input is optional )
* Communication interface(RS232/RS485)
* Network solution, IP address can be set
* Built-in detection, fault alarm, reminder function
* USB interface

* Alarm and show automatic message reminder

Installation Place Requirements

※ Distance from the wall to both sides more than 800mm, and to the front more than 1500mm.  

※Provide independent distribution switchgear, humidification condensate drains, and external power connector device is necessary.  

※ Ground level, well-ventilated, no flammable, explosive, corrosive gases and dust; 

※ No strong electromagnetic radiation nearby;  

※ With floor drain(less than 2 meters from the refrigeration unit);

※ Venus Floor load capacity: not less than 800kg/ m2;

※ Leave adequate space for maintenance

After-sale service:

Feedback within 2 hours, offer solution in 48 hours and help to solve the problems.

Package: 

PP film first, and then 10mm foam between machine and the case, and outside is standard export plywood case.

Model Features

Model

BTH-2000-40

2000L

Temp. range

-40~150°CC

Display resolution

0.1°CC

Temperature stability

High±0.5°CC ,low ±1.0°CC

Temperature uniformity

±2.0°CC

Heat up time

-40°CC ~+100°CC< 45 min

Pull down time

+20°CC ~-40°CC< 60 min

Humidity range

20~98%R.H,(standard),

'10~98%R.H,(with humidifier)

Humidity constancy

±2.5%R.H

Humidity uniformity

±3.0%R.H

Interior Dimension(mm)

1000W*2000H*1000D

Exterior Dimension(mm)

1280W*2260H*1950D

Interior material

Stainless Steel Plate(SUS 304)

Exterior material

Baked Painting Steel Or Stainless steel(SUS304)

Insulation material

Rigid polyurethane Foam and Glass Fiber Wool

Total power

16KW(heater 6KW included)

Max current

50A

Water Consumption

4.5L/hr

Ambient Temp.

+5°CC ~+35°CC

Power Supply

 

AC 380V±10% 50Hz ,3 phase 4 wires +Ground Wires

Weight

800KG

Sight window size

460*560mm

Sample holder

2 pcs

Fittings

cable port(portΦ50mm)*1, chamber lamp*1, power cable *2m

Safety device (standard)

NFB, over pressure, over heat over current protect, over temp. protect, over load protect for blower, dry heat protect

Control System

Balanced Temperature & Humidity Control (BTHC)System

Refrigeration system

Air Cooled (Water Cooled is option)

Hermetic compressor

Hermetic compressor                               Single stage refrigeration system,                     CFC-Free refrigerant(HFC-507/HFC-23)

CFC-Free refrigerant(HFC-507/HFC-23)

Controller

7-inch LCD Touch Screen panel

Operation model :Program or fix point running

Memory capacity :120programs,1200steps,

All repeat 999 cycles, part repeat 99 cycles

Note: 1. We reserve the right to change specifications without prior notice                                                    2. Customized sizes and configurations available

Note

1.Average temp change rate between highest and lowest temperature without any load and heat dissipation, Refer to IEC60068-3-5 for more details)

2.Performance is measured in the ambient temperature of + 25℃ and sensors are placed at  the outlet of  air conditioning unit ;

3. Customized sizes and configurations are available.

Inner view


Hot Tags: solar chamber, solar test chambers manufacturers, suppliers, factory, wholesale, cheap, best, buy
Related Products
Feedback
Feedback
Your comments are welcome!
For more information about our brand and products, please feel free to contact us!
Please enter your email address:
Contact Us
Address: Futian Free Trade Zone, Shenzhen, China
Tel: +86-755-33320899
Fax: +86-755-33320008
E-mail: testequipment@baclcorp.com
Copyright © 1996-2016 Bay Area Test Equipment Inc All rights reserved.